Skip to main content

Replies sorted oldest to newest

No effect when you goose the gas? Dirty (clogged) gas filter, clogged brass filter sock in the bottom of the tank, carb floats/needle valve stuck?  Sounds like a fuel issue to me.

Do you have an electric fuel pump?  If so do you hear it run at startup and then occasionally?

Do you have a vent to fuel tank?  Either a vented cap or a small hose off filler tube.  Try running it with the fuel cap removed.  Could be vent is blocked.

Last edited by WOLFGANG

That sounds like a classic clogged fuel filter.

Get it up on jackstands or on a lift at a local mechanic and follow the fuel line from the tank (up front) back to the engine.  The fuel filter could be anywhere along the length.  Once found, replace it with one similar.  While checking, look for any sharp corners in the line that might be crimping it partially shut.

If it is a see-through plastic filter, please do not use another one of those.  Instead, go to a local NAPA store and ask for a NAPA Gold 3031 metal-can fuel filter and use that instead.  Much better filtering and it won't melt under heat and set your car on fire.

You probably won't have to pull the tank (but it is really easy to do, no matter what).  Instead, you can get to the outlet under the tank by pulling the passenger side front wheel to gain access to the underside of the tank.  Drain the tank and then remove the outlet (there will be some gas spilled even if you drained the tank) and check for debris or clogging.  There may be a small screen on the outlet up inside the tank - Or maybe not.   Use teflon tape on the threads when you replace it.

The only other things affecting it might be (a.) a rubber fuel line that has grown mostly shut, (b.) a clog at the carb pilot valve (unlikely, given that it runs for 15 minutes) or (c.) a weak fuel pump (again, unlikely).

Good Hunting.

Last edited by Gordon Nichols

A temporary fuel pressure gauge T'd into the fuel line in various places will give you some info, not guesses. Try before and after pump, before and after fuel filter. Also, just for the heck of it, try removing the filler cap. Sometimes they go bad and won't let any air in as the fuel level goes down, that could definitely be it.

Points? could be condenser going bad. Electronic ignition module? Could be that going bad as well, also could be the screw that holds the module to the advance plate in the distributor.

90% of fuel problems are ignition problems.

I had a dune buggy that would run a few miles and the engine would mysteriously stop. I would sit on the road side and mess with it and it would finally start up and run perfect then a few miles later the exact same thing would happen. I finally figured out that the fuel tank vent tube was bent and pinched so no air could get into the tank to replace the fuel being sucked out and the engine would then be starved of fuel.. As I sat on the roadside the little bit of air that could get by allowed the tank to fill with air again.  I cleared the kink in the fuel tank vent tube and  all was well. Do you have a vented cap on your fuel tank? Is the tank vent tube clear and open?

Well, after a bunch of web surfing and spec reading, Jim is absolutely right - Don't use any Teflon-based product for sealing threads on fittings for gasoline.  Teflon will slowly dissolve in a gasoline/petroleum environment.  

Bathroom faucet, yes.  Gasoline fittings, no.

Instead, use something like this (they have it at NAPA, too):

https://www.amazon.com/Permate...essing/dp/B007VIGCJW

Ray Shanahan posted:

I am having a problem with my engine. I have a 1600cc with dual webers and it dies after running for 15 minutes. I have swapped the coil and it still occurs. Any suggestions?

Hi Ray

i am also having problems with my 1600 cc engine thanks to the negligence of my incompetent mechanic.

i also have dual Weber’s. 

Do you know the details of your engine?

is your engine of 1641 cc (100.5 cui) displacement, delivering 67 kW (91 PS, 90 hp) of power.

When I was a kid my dad had a 24' wood cabin cruiser with a 4 cyl inboard Gray marine engine.  One day the engine died during fishing for blowfish.  The copper 20 (?) gallon gas tank had collapsed (vacuum sucked it near flat) - we discovered mud dabber wasps had filled the tanks air vent out the sided of the boat with red clay.  Poked it clean and fortunately engine restarted.  Weren't any Tow Boats US in Barnegat Bay NJ back then (and hardly any Blowfish now)!   

It wouldn't start after it died.  Thanks for the suggestions. I would hate to have to pull the tank, but maybe that is the problem.

 

I'm in the process of having an aluminum tank fabricated because, I hate to say, removing and cleaning the rust out of my tank has become an annual event since I left my car sit for a couple of years. 

Removing the tank is also a good time to replace the pre-pump filter, and cleaning the wire mesh filter inside the tank.

Last year I replaced the fuel pump/filter with an Edlebrock pump up front and installed a Malosi FilterKing regulator in the engine bay and I STILL have to blow out my main jets a couple of times a year. 

Last edited by dlearl476

Take your tank to a radiator shop, have it steamed out and chemically cleaned, then coat it with some good ethanol-resistant stuff. Replace all the rubber hoses, blow out the steel lines. Give the carbs a proper off-car rebuild. 

Put Stabil or similar in the tank and run it for at least 15 minutes before storage. Then forget about it.

P.S.: The main jets do not clog. It's the idle jets that clog as the orifice is very small.

@DannyP posted:

Take your tank to a radiator shop, have it steamed out and chemically cleaned, then coat it with some good ethanol-resistant stuff. Replace all the rubber hoses, blow out the steel lines. Give the carbs a proper off-car rebuild. 

Put Stabil or similar in the tank and run it for at least 15 minutes before storage. Then forget about it.

P.S.: The main jets do not clog. It's the idle jets that clog as the orifice is very small.

Doh. You're right. 

 

I'm going the aluminum tank route because they only place left that boils tanks around here charges $150 and doesn't even paint them. Not to mention, whoever built my car took a sledgehammer to the bottom of the tank to get it to clear the steering column, putting the spigot 1.5" above the lowest point in the tank. It's a mess. An aluminum tak will be beautiful and it will never rust. 

Post Content
×
×
×
×
Link copied to your clipboard.
×
×