Skip to main content

I got my new VS exhaust and am installing it today.  I have the headers tight to the manifold but all other bolts are slightly loose.  The left pipe only has about 1/16 clearance from the plastic bumper and the right pipe has about 3/8".   Is there any trick to adjusting these so there is proper clearance from the bumper?20210825_115234

Attachments

Images (1)
  • 20210825_115234
Original Post

Replies sorted oldest to newest

I bought the Porsche replica version 155-204-05200 with the pipes lowered in comparison to the VW version.  Its just a little too close for comfort given that they flex a little when the engine is running and I don't want to melt the bumper.

I'll try tightening everything down, but it doesn't look like that will change the position from where it sits.  I'll see if the bumper can move a little up too. 

I don't know guys.   I have everything snugged in now and the driver side is now touching the body and bumper.   There is about 1/4 on the passenger side.

The tips on this one actually sit about an inch in from the bumper unlike the tri mil that protruded out pretty far.   Therefore no way to get any leverage to push down on it with my foot.  See the pictures below.

Is there any way to lower the engine slightly or anywhere else to adjust to make this work?   Clearly not an option to have it touching and melt my beautiful bumper.

20210825_14383020210825_143716

Attachments

Images (2)
  • 20210825_143830
  • 20210825_143716
Last edited by MarylandGuy

To protect the chrome surface of the exhaust I would apply the english to it in the following manner: Make a loop with a nylon strap and drape it over the exhaust tip where it rubs on the bumper. Insert a length of wood or metal pipe into the open/hanging part of the loop making sure nothing touches the chrome. Press down on the wood or pipe with your foot and see if that moves it enough.

Last edited by Robert M

@MarylandGuy

I had a similar problem with my VS exhaust.  Before you start trying to tweak it as described above, contact MT at Vintage Speed.  He supplied me with spacers, gaskets and longer bolts to put between the flanges on top of the muffler and kick the muffler down a small amount.  I'm sure you could use different thickness spacers to adjust the side to side difference also.

Email MT at Vintage Speed, he responds quickly and I have found him to be very helpful.

James

I heard back from VS and the spacer solution that @James has will cost me $60 with 1 week shipping.   Looks like something I could source locally since it is just 2 spacers and longer bolts.  Does this just go in the connection between the headers and the exhaust so it pushes it down some?   Amazon has stainless steel 8mm kits for about $22 + shipping an will probably be faster than coming from Taiwan. 

https://www.amazon.com/FORTLUF...54515195937&th=1

Last edited by MarylandGuy

@MarylandGuy

The spacers are basically the same flanges that are welded to the exhaust pipes.  SS flanges that are laser cut to the same shape and ID as the flanges.  He also supplies another set of gaskets to match the flanges.  You will need one on each side of the spacer.

You are correct, it simply pushes the muffler down a small amount.  If I recall correctly, the spacers were about 1/4" thick and moved my tailpipes down about 1/2" from the body.

You could make or buy the spacers, but I don't think they are a standard shape/size and require his gaskets to match.  Check the dimensions on the ones you linked to make sure they match.  The bolts are easy to get.  However, for 60 bucks, his makes for a really clean installation and work great.  Just my opinion.

James

Last edited by James

MarylandGuy:  A lot of the fixes suggested are "KISS" type and should be considered before getting too clever.  You are going to be okay because you instinctively went to modifying the part to fit the car not vice versa.  Modifying the part usually means you can go back if something doesn't fit/work

I have a lowered Thunder Speedster.  For future reference, I found the VS lowered bus setup worked well for me.  It tucks up underneath, single out pipe runs parallel to the muffler.  There still may be a picture on the Aircooled site.  I'm a VS fan, I like their stuff well made with good hardware.

Keep the shiny side up, and stay between the ditches.

20210824_193905My 10 year old son Henry and I took a 2 hour adventure today to a muffler shop and Napa + Advance Auto and got the parts for $25.  Not as clean as the exact VS matching parts, but enough that I will be able to put in spacers and lower it to fit without modifying my car.

Getting a gasket with a 1.75 diameter hole proved a fools errand locally so I just got a sheet of gasket material and will cut to match tomorrow.   I'll post some pics when I get it all setup and will do a separate detailed post on the full VS install for future adventurers.

Side note that Henry isn't into cars like my older son Brady (12, below in picture removing the Tri Mil) and was a bit aggravated that I dragged him along, but he is 10 and doesn't get a vote yet.  I have to believe he will be positively impacted by my madness and quality time with Dad doing stuff that really is cool.

Attachments

Images (1)
  • 20210824_193905
Last edited by MarylandGuy

Well I'm feeling a little defeated.   I got it all back on with the spacers and it is hardly and different...  maybe 1/8 inch lower.  I'm done for the night and need Miller time.   

I will loosen everything up again tomorrow morning and see if something can. Move around to get it lower. 

Here is a picture of the gaskets I made and the flanges/spacers.   The metal sheet is what I cut them out of.20210827_151905

Attachments

Images (1)
  • 20210827_151905

I loosened everything again this morning and got it to reposition down about 1/4" from the fiberglass, but not feeling great about it.   The point of contention is the connection to the heater boxes.   The exhaust wants to mount level with them and they are rock solid mounted and won't give any downward angle.   The way I got the extra 1/4" was to have everything loose and then mount the heater box seal bracket first with a bend in the connection.   Then I tightened everything else.  I'm not sure that position will hold after I drive it a while though.   Here are some pictures.20210828_09165820210828_09175120210828_09284620210828_092829

Attachments

Images (4)
  • 20210828_091658
  • 20210828_091751
  • 20210828_092846
  • 20210828_092829

I agree with Alan; some heating up and tweaking should get you there. Like I said before the one in my car hangs down for some reason (see earlier post with photo); the tailpipes are not fully horizontal with respect to the ground but I believe I’ve seen these units on other cars with varying degrees of levelness. Not sure if it’s due to inconsistencies on the car builds themselves or the adjustability of the muffler. This is how mine looks from the back.81C0A79A-9AE3-4B7E-90E5-87FDC770F7A6

Attachments

Images (1)
  • 81C0A79A-9AE3-4B7E-90E5-87FDC770F7A6

I think you all are right.  At this point, there is no more basic adjustment to be had, so the shape will need to be modified... VS has my latest pictures and is going to have their engineer look at it, but not sure what they can really do at this point except for maybe create a custom set of spacers or headers that give it a different geometry. 

I have to see what local muffler shops I have around...  Alan seems to have "a guy" for everything, but I do not in my area.

I would try googling "Custom Car Exhaust Shops near me" and see what pops up.  I just did that here and I know all of the top three are used by the Hot Rod guys because they ALL need custom-tweaked exhaust systems - Their cars are even more custom and weirder than ours are.  Your area is no different than Massachusetts - Hot rods are everywhere.

I've been looking at your photos and we both realize that a spacer alone isn't going to drop the exhaust tips AND keep them level.  There's going to have to be several steps taken to drop the muffler and keep the exhaust tips horizontal and a custom exhaust shop deals with this stuff all the time.   They'll know what to do.

@MarylandGuy The spacers worked well on my car, however the difference could be that you are running heater boxes and I have J-pipes.  The J-pipes allowed the muffler to move down easily.  I got about 1/2" drop at the body with the 1/4" spacers.  Also, the exhaust gasket material from VS is a little thicker and allowed more compliance at the connections. 

As others have suggested, it may be time to tweak it a little with some heat.  Just be careful, stainless moves a little differently than carbon steel when heated.  As Gordon stated above, the tips will probably not be perfectly level when you finish.  Mine have a slight angle, but are not noticeable unless you crawl under the side of the car and inspect carefully.   Looking good!

I agree with @James that my main issue is having heater boxes since they are mounted to the back of the engine and have zero flex.

This morning I did some driving around my town because not all of these places have websites or show up on google.  I was able to eventually find a place on a backroad only about 10 minutes away who has a whole car fabrication shop where they specialize in japanese imports and racing modifications (fast and the furious).   I talked to a younger guy named Justin and he is going to free up a lift for me tomorrow morning so we can take a look and do a little heating and bending to get it in place.   He showed me his project car where he is custom fabricating a drag car from the ground up using parts of an RX7 body, Honda engine, miata suspension and full custom tubular frame and roll cage that he built himself.   I think I'm in good hands, but told him not to expect me to race him in my speedster when he is done his project. 

I'm hoping this will be the end of my drawn out saga and loss of prime driving weather.

Post Content
×
×
×
×
Link copied to your clipboard.
×
×