Skip to main content

Replies sorted oldest to newest

@JB356SR posted:

Hi everyone,

I am looking to mount my oil filter.I would like to mount it horizontally off the rear driver side bumper bracket and I will be mounting a oil cooler in the future. My question is, does it matter if I mount it horizontally or vertically?

Only when you change it. There’s no way I would mount an oil filter any which-a-way but vertical. But then I’ve dumped about a gallon of oil in my 968 engine compartment over the years because the filter is horizontal on the side of the engine block.

Yeah, every time I see a horizontal filter on any engine I wonder "what the hell were they thinking?"

I have mine mounted vertically, screw-on flange pointing up so that when I unscrew it, it hold the oil in it with minimal leakage/spillage.  I also pre-fill the new filter with oil when I do an oil change so there is never a massive air bubble in the system at first start-up.

I bolted my mount to the body frame member that forms a square horse shoe around the engine.  It's positioned so that hose and valve cover access is easy.  Been there for 20 years and the mount failed last year (it was a flimsy aluminum plate affair that I had made) but other than that has been trouble-free.

I documented my set-up on here years ago:

https://www.speedsterowners.co...-1-mechanical-layout

But the layout photos are long lost (Photobucket started charging for use) so here is the placement of the cooler and filter in a series of photos - It works great.  Just to be clear, the filter mount itself has been bullet-proof.  The piece of diamond plate angle stock I used as an adapter was too thin and not up to the task, so it failed and was replaced by a steel equivalent - That's been fine.  Be careful of where you mount the filter and hoses so that valve cover access isn't impeded.

Cooler and filter locationsCooler and HosesFilter and return fittingsFilter mount Afilter mount BFilter Mount

Attachments

Images (6)
  • Cooler and filter locations
  • Cooler and Hoses
  • Filter and return fittings
  • Filter mount A
  • filter mount B
  • Filter Mount
Last edited by Gordon Nichols

Q:

Yeah, every time I see a horizontal filter on any engine I wonder "what the hell were they thinking?"

A:

I can't speak for anybody else, but what I was thinking was, "gee, if I mount this sideways, it doesn't stick below the bottom of my fender, all the lines fit nicely, and it'll neatly drain into the catch pan without getting oil rolling down my arm, through my armpit, down the inside of my shirt, and into my tighty-whities", or something to that effect.

If you gentleman like giving that filter a quick twist, then having oil cascade across the entire outer surface, and drip randomly off some part of the bottom, then by all means, carry on. I'll be over here, not losing a drop, and not leaving a black rivulet from my hand to my nether-regions.

PS: with an Accu-Sump, I have oil pressure every time I start the car (and before I'm cranking the starter as well).

Your mileage may vary.

Last edited by Stan Galat

.

Mine was mounted horizontally (to keep it more tucked up and out of the way).

Yeah, it's a bit more of a pain to change the first time, but eventually you work out a procedure and, after that, it's no biggie.

Drain sump first. Position catch pan under filter. Slowly  loosen until dripping starts. Wait for dripping to stop. Unscrew the rest of the way, holding filter horizontally as you pull it free. No more oil will run out unless you tip the open end down, but you do that into the catch pan.

Harder to describe than to do, but bottom line is it's easily done with a minimum of spill.

Not a reason to avoid mounting horizontally if that works out better for other reasons.

I'm reminded of how hard it seemed removing idle jets on Webers the first few times. After a while, you get the hang of it, and it becomes nothing to stress over.

As a species, we have been solving problems like this for millions of years. This is far easier to master than using a ketchup bottle.

.

@Stan Galat posted:

Q:

A:

I can't speak for anybody else, but what I was thinking was, "gee, if I mount this sideways, it doesn't stick below the bottom of my fender, all the lines fit nicely, and it'll neatly drain into the catch pan without getting oil rolling down my arm, through my armpit, down the inside of my shirt, and into my tighty-whities", or something to that effect.

If you gentleman like giving that filter a quick twist, then having oil cascade across the entire outer surface, and drip randomly off some part of the bottom, then by all means, carry on. I'll be over here, not losing a drop, and not leaving a black rivulet from my hand to my nether-regions.

PS: with an Accu-Sump, I have oil pressure every time I start the car (and before I'm cranking the starter as well).

Your mileage may vary.

Do you have any pictures of your set up?

@DannyP posted:

Gordon, I really like what you did there. But multiple 90s aren't great for flow unless they are sweeps...

AN-8 180s are like $20 each, but are a smoother way to reverse direction. As my buddy Stan says, buy/cry once.

That may all be true, but its been working and cooling fine for 16 years now without a hiccup.   I never needed any 180º connections - the worse is an occasional 90º but on the latest hose routing version I used more 45º fittings due to better routing (all things get better after you think about it more).

So I guess you can mount the filter any way you wish and then just work up a method of spinning it off and catching the drain oil.  Whatever fills your drain pan!

@JB356SR posted:

Do you have any pictures of your set up?

Not super relevant, as I've got a dry-sump, but this part of the piping is not dry-sump specific, and could be (and was) used before I did the conversion.

Here's the best pictures I've got.image_50401025image_50455553image_50431745

image_50449153

The top picture shows the orientation of the filter base and oil cooler. The filter base is a JayCee part - it's a pressure bypass filter base. If the oil pressure rises above 80 psi, it bypasses into the sump of the engine. That's the line labeled "bypass".

The hard-line coming into the center of the filter base is the AccuSump line. I've got the AccuSump mounted inside the engine compartment running east/west just behind the license plate.

The two AL hard lines underneath the filter base are the lines from the Mocal thermostatic bypass filter base, and run to the 96 plate cooler. I had a radiator shop seal off the bottom threads on the cooler, and I tapped AN fittings into the sides of those fittings (which were then AL-soldered) so that no fittings stuck below the bottom of the fender.

The second picture is with all the braided lines pulled off, but you can see the orientation of the filter and cooler in the wheel well. The bottom picture is the entire layout with the dry-sump lines.

When I do an oil change, I don't lose a drop.

Attachments

Images (4)
  • image_50401025
  • image_50455553
  • image_50431745
  • image_50449153
Last edited by Stan Galat

.

We used a Setrab filter holder that allows flexibility in how the bracket may be oriented and attached and in how the hoses may be routed.

This is just a filter holder, it doesn't incorporate options for bypassing the filter, but Setrab does make a whole line of stuff that does:

SetrabFilterHolder

Here's how it looks installed on my car. It's tucked up enough that getting good photos is difficult, but this may help. Notice that the filter is completely above the bottom of the bumper:

FilterMount

.

Attachments

Images (2)
  • SetrabFilterHolder
  • FilterMount
Last edited by Sacto Mitch

20180827_12201320180827_12203320180827_11581420180830_082403@Stan Galat : Extra ingenuity points for the Accusump plumbing into the oil filter mount! I wouldn't have thought of that. How easy/hard was it to bend up the aluminum hard lines? That looks great, and again, ingenious.

Bonus points for the custom oil tank.

The Autocraft pump looks identical to the NLA Bugpack, with the exception of the scavenge/suction connection. The Autocraft does that externally on mine through a bolt-on sump plate.

The cool thing about Autocraft is they'll build whatever you want. I specified AN-10 on suction and pressure stage inlets. They also do what they call a 1.5 stage that uses the VW pickup tube. 52mm suction and 26mm pressure gear sizes.

Attachments

Images (4)
  • 20180827_122013
  • 20180827_122033
  • 20180827_115814
  • 20180830_082403
Last edited by DannyP

Add Reply

Post Content
×
×
×
×
Link copied to your clipboard.
×
×