Skip to main content

Classified postings do not allow for discussion (replies are not allowed).  Direct message the member if you would like to discuss the item.
The Classified section is open to any individual (non-commercial firms) posting of items for sale. Members posting commercial advertisements must be enrolled in a Supporting Merchant program. 
Postings without relevant details (PRICE, location, condition, etc.) will be deleted.

I'm sure you won't believe this....With 9 vw engines, a Buick v6, a 2l 914 engine, and 2 kaynor electric motors for the vw all sitting on the garage floor it has been a really hard choice.. it had a 1300 or 1500 SP motor in it that was weak so I decided to put this 2332cc type one into it. I also added a new bluetooth stereo, and replaced the red cracked fiberglass seats with these black ones.Sent from my Verizon, Samsung Galaxy smartphone

Attachments

Images (4)
  • 20160720_121140
  • 20160720_121819
  • 20160720_121801
  • 20160720_125528
unofun posted:
I'm sure you won't believe this....With 9 vw engines, a Buick v6, a 2l 914 engine, and 2 kaynor electric motors for the vw all sitting on the garage floor it has been a really hard choice.. it had a 1300 or 1500 SP motor in it that was weak so I decided to put this 2332cc type one into it. I also added a new bluetooth stereo, and replaced the red cracked fiberglass seats with these black ones.Sent from my Verizon, Samsung Galaxy smartphone

I like the idea of the single Weber in the center but many will poo poo the idea. What have you done to the inside of the engine ? Thanks.

Mt Type IV is stronger and smoother than the day I picked it up at Jake Raby's 35,000 miles ago.  For me the ultimate test is the 13 trips home from Carlisle using I-40 and  that 8 mile super steep section of I-40 East of Asheville where with my original 1915 Type I had to use second gear and sometimes even third to ascend that stretch.  Big trucks can go only 30-35 mph there.    Now on that road I do 75 in 4th gear with ease and a big reserve in power.   Never had to stop mid-trip for anything but gas, and never a backfire or failure of any sort to date.

Interesting side note---that stretch of I-40 going East (down the mountain),  it is so steep that at every 1/2 mile or so there is a runaway truck emergency exit with a deep sand surface and these exits are positioned so that  they turn up a hill for trucks with brake failure to use to stop quickly.  That part of I-40  is steeper than anything I have ever seen in the country anywhere.  For some reason the highway engineers went straight up the mountain side rather than going around it like they do even in the Rockies.  Did I say it was steep??

Anyone know that stretch I'm talking about?   Imagine how this type IV  pulls on a flat road.  I love the idea of Suby power but I'm very satisfied with this engine. I don't have ac but there is an Espar heater making it a true year-round driver here in Dogpatch.

Wolfgang---best of success with whatever way you choose to go for power.

WOLFGANG posted:

I like the idea of using the T4 2L engine.  A few mods and 120-140 dependable HP. There is so much room in the 359 that a T4 with the flat pancake cooling tin would easily fit and actually be easier to service.

Yes Sir, that’s what I am running now a Porsche 914 two litre T4 with 96mm x 76mm bore and stroke makes 2.2 litres with stock cooling   It has lots of room for the stock fan and room enough for a nice dual exhaust that is far away from the fan which is something I always hated in my Porsche 912 with T4. Their it was so close that the fan sucked in the hot air around the muffler!

Tuscaloosa, yeah damned cool. In the late 1700s four ancestor  brothers established the town of Fosters , Alabama which is very close to Tuscaloosa.  They were awarded land, like 60 miles  (miles!)  down along the Black Warrior River, as reward for  their father's service in the Revolutionary war.  They  shipped cotton directly to England from their landing on that river.  (Google "Fosters Landing", Tuscaloosa, AL.)  

Not very PC but I have a sheet showing slaveholders in Tuscaloosa County showing the 15-20 ancestors who owned 75-80 "workers".  Two of the plantation homes are still there and recently one changed hands and is still occupied.  Having an interesting time with family genealogy.  One of the most startling finds is a pay stub to that Revolutionary War ancestor (Captain John Foster) showing his pay that month when his unit was at Valley forge with G. Washington. I got that in a genealogy research place in New Orleans a few years ago.  I got my sister into DAR with this research and myself and son, Russ in the Sons of the American Revolution  (SAR).

Yeah--Tuscaloosa is very cool.

Iam -Ray---why did you bring Tuscaloosa up?

 

Last edited by Jack Crosby

Thought that this was interesting:

Ok,, just have to clear up some of the misconceptions about the 359. I have collected a lot of information on them, over the past 4 years,, and even discussed them with a former CMC employee, so I am reasonably sure of my statements.

The 359 was layed up in its own molds,, and is not a 356 with extra pieces grafted on. Mine certainly is made with single layups. The body shape is very different from a 356's,, and the wheel base is 89.5 inches. Mine weighs in at 1760lbs (with a 1/4 tank of gas). I do note however, that the literature I have says it can weigh up to 1875lbs, depending on engine choice. The only panels that it shares with the 356 are the doors and windshield assembly.

My car has had 3 years of pretty spirited driving,, and it is not showing any serious cracks. Previous owners drove it for 3 more years prior,, but I think they were relatively gentle with it. I have certainly seen lots of cmc 356's with a lot more cracking. So I guess I am lucky.

The kits came with a filler panel where the oem Porsche center reflector could be mounted. Some owners will throw the 911sc reflector cause it looks so much better. But you have to look long and hard to find one at a reasonable price (yes,, I did). I believe Porsche could care less about 356 replicas or any of the other older designs that might bear its likeness. They are not like Ferrari or Lambo' in this respect, and are not likely to sue anyone. 359 kits were produced by CMC mostly,, and a few by ThunderRanch. I don't think any kits were manufactured overseas,, but kits shipped everywhere,, and could certainly have found their way back.

Just want to add,, that this site is the best. And my trip to Carlisle a few back was a gas. I still have my Speedsters Mug, and put it to good use on special occasions !! Thanks Gang !! Alan

WOLFGANG posted:

I was always trying to find the build manual to have it scanned and loaded to SOC.  It seems like it sits on a full VW pan.  I have some photos of the molds used to flash the 359 body sitting out behind a garage somewhere. 

359-1359-2359-3

 

No, the body sits on a custom frame with a 89.5 inch wheel base, the same as the original 959 and 911. The VW pan has a 94.5 inch wheelbase. The 356 was shorter then the VW and 911. Thanks for the attachments!

You can see what CMC did with the 359 after all  they had the centre section from their old Speedster design. Only the doors on the 359 are interchangeable with the other CMC Speedsters. The whole car is longer and has a wider track to look like the real 959 Speedsters and they share the original wheel base of the 959. The Porsche 911 Speedster copied the old 356 Speedster windshield design. Becker used the 911 Speedster windshield design to create their real 959 Speedster. Of course CMC already had the old style 356 Speedster windshield design that they carried over to the 359 Speedster. later CMC even produced 959 Body Kits to convert Porsche 911's to make them look like 959s!

TOP PIC: CMC 359 Speedster (959 Speedster replica).

BOTTOM PIC: Becker 959 Speedster (959 based Speedster):

IMG_2007959conv

Attachments

Images (2)
  • CMC 959 Speedster (359)
  • Becker 959 Speedster
Last edited by Clark

I found some more info on the authentic 959 Speedster:

In 1987, Porsche delivered a Porsche 959 to German race driver Jürgen Lässig; who, owned the car up until he had an accident on the Autobahn in 1988. The 959 had flipped over and was severely damaged in the collision with an Audi 80 on the A 81 at Singen on the top, right front and on the side. From there it was bought by a company called Auto Becker. The damaged car went to Auto Becker in Dusseldorf where it was converted to convertible. The engine technology and the complete electronics remained untouched; Stiffeners were welded in. Becker chopped the roof off and fit a 911 Speedster windshield. They also fit a folding soft-top. Afterwards, the 959 Speedster was shown at the IAA show in Frankfurt. A collector from the US bought the car for allegedly 3 million D-Mark. The car can also be converted at any time to a normal Cabriolet, or hard-top configuration. Becker preserved the original roof to be installed if so desired as a removable hard-top - by way of a few handles and the exchange of windscreen and hood. This original style roof was supplied in a very large custom made padded box. The 959 Speedster was tested by Sports Car International in February 1992. From the waistline down the car looks like the original 959 which it is. From the waistline up the 959 in Speedster mode looks like a 911 Speedster.

It is interesting that the CMC replica 959 Speedster debuted in 1989. Reference, Peterson's Kit Car Magazine; issue, March, 1989. Therefore, CMC was likely inspired by Auto Becker 959 Speedster and got the idea to create the 359 Speedster from their replica Speedster. By then, CMC had vast experience with Speedster replicas and they wanted to make their own flag ship car for the US market since at that time all original 959's were prohibited from entering into the USA. The 359 was layed up in its own molds, and is not a 356 with extra pieces grafted on. It was certainly made with single layups. The body shape is very different from a 356's,, and the wheel base is 89.5 inches like the original 959.

Bill Prout posted:

I never liked the 959 aesthetically.

I can understand that!

I know I am in the minority here and I have owned a 57 Speedster too as well as several 911's and P-cars. But, I always liked the 959. Never really liked the 356 Speedster all that much. i know they are worlds apart. The first time I ever saw a Speedster in person I thought it looked like a upside down bathtub! Lol.

Clark

57 356 Speedster replica, 69 Porsche 912, 72 914, 73 911 RS replica, 81 924 Carrera, 82 924, 83 944, 88 928S4,  91 911Carrera 2, Dino Ferrari replica with 455 V8, 959 Speedster replica

 

Last edited by Clark
WOLFGANG posted:

Interesting Blog by guy that worked for CMC in the era. He says the 359 uses thicker fiberglass than 356 shells.  Hence, heaviest shell CMC produced.  Engine bay was made to fit larger, more powerful engine to compensate.

https://classickitcars.wordpress.com/about/

https://classickitcars.wordpress.com/

Check this CMC mod - bonding 356 body parts to a 911 to create a 959.

959cmc2

And a 959 Targa conversion.

959CMC

Trio of cars (Targa, Cab, and Coup) built on Real Porsche’s built at Classic Motor Carriages in the late 1980’s.

They were called the “Ultima” and for a modest amount your Porsche 911 could be fitted with a fiberglass body kit that would make it look like a real Porsche 959.

Add Reply

Post Content
×
×
×
×
Link copied to your clipboard.
×
×