Skip to main content

Good evening fellas!

 

I thought I'd start another thread on my Speedster progress since you guys hijacked the snot out of my last one! LOL!!!

 

I had taken my crankcase and heads to my machinist and things went south. The thrust cut and line bore were done and when fitted together there was a 0.008 gap at the center of the case. It turned out the case was warped so I hunted around and found another one to work with. Parts are currently at my machinist being worked on.

 

 Again, this is will be a mild 1600cc motor I will use to debug the rest of the mechanical functions of the car. I plan to later change out the motor with something with a little more pep.

 

Meanwhile, I've been cleaning and painting parts that I will still use on the motor. It's probably old news to some of you but I'm using Crown PSC 1000 for my solvent. You can purchase 5 gallon cans at your local tractor supply store. This stuff is awesome, it reminds me of the solvent we used in auto shop as a high school kid. I'm also putting together an engine test stand. I've never made one before but always want to mess with a motor outside of a vehicle.

 

What else… trying to get my rear axles off! I've used Kroll oil, P-Blaster, cheater bar and the "Torquemeister" torque multiplier and so far no luck. I ordered a 36mm 6 point impact socket and will try that with my air/electric impact wrench. I'll torch the nut if it need be.

 

Nuff' said for now, that' my update!

 

Speedster_Motor_01Speedster_Motor_01aSpeedster_Motor_01bSpeedster_Motor_02Speedster_Motor_03Speedster_Motor_04Speedster_Motor_05Speedster_Motor_07Speedster_Motor_08 

"All I need are big dreams and open highways..."

Attachments

Images (9)
  • VW Motor Test Stand 1
  • VW Motor Test Stand 2
  • VW Motor Test Stand 3
  • Crown PSC 1000 -1
  • Parts Cleaner
  • Exhaust Paint 1
  • Exhaust Paint 2
  • Exhaust Paint 3
  • Torque multiplier, Torquemeister: Still stuck...
Last edited by vdubuslife
Original Post

Replies sorted oldest to newest

I recently removed my axle nuts and I'm not sure they were on with even 100 ft lbs of torque. Both sides came off easy. I was prepared for a high degree of resistance so I left the tires on with the lugs nuts loosened but finger tight, put on the 12" breaker bar and socket, took the handle off my floor jack and slid it over the breaker bar, had my son hold the socket in place, and when I went to put some pressure on it, it came right off with very little effort.

After I change the axle seals on both sides I reversed the process and this time I pout some real force on it and probably got it to three hundred or so foot pounds of torque. Then just a tiny bit more to fit the cotter pin in the hole.

Alan Merklin posted:

If you have used the "Torquemeister" with 35 lbs of force ...this equates to 240lbs  or so it isn't going to come off easily …You may have to use torch heat than the Torquemeister and or cut the nut through as far as you can and slit it with a chisel then back it off the stub axle. 

Hi Alan,

I'm skeptical the impact wrenches are going to work tomorrow by itself. That being said I'm looking at purchasing a torch. I've seen the "Bernzomatic" offerings and they have models specifically for rusted bolts situations. 

Do you have a preferred torch you use? I want a small handheld that I can use on occasions such as this. 

This is a link to the Bernzomatic type. 

https://www.bernzomatic.com/ge...elect-Torch.pdf.aspx

 

Robert M posted:

I recently removed my axle nuts and I'm not sure they were on with even 100 ft lbs of torque. Both sides came off easy. I was prepared for a high degree of resistance so I left the tires on with the lugs nuts loosened but finger tight, put on the 12" breaker bar and socket, took the handle off my floor jack and slid it over the breaker bar, had my son hold the socket in place, and when I went to put some pressure on it, it came right off with very little effort.

After I change the axle seals on both sides I reversed the process and this time I pout some real force on it and probably got it to three hundred or so foot pounds of torque. Then just a tiny bit more to fit the cotter pin in the hole.

Double lucky, you were able to remove the axle nuts easily and no mishaps for being so loose. 

As far as tightening the axle nuts I plan on using the Torquemeister for that. I'll be able to use a 3/8" drive torque wrench for that part.

If you get a torch and want a lot of heat, Propane won't cut it (no pun intended).

Get a MAPP torch - yellow cylinder, different jet size, LOTS more heat, about the same cost.

I always use an 18" long 1/2" breaker bar with a 6 foot piece of pipe on it, along with a resistance bar attached to the hub bolts.  Heat the nuts up and hang on the end of the pipe and they should slowly loosen (and I only weigh 160 lbs!)

Last edited by Gordon Nichols

Just a note about the cast axle nut thing Jimmy posted a picture of- it works best if you're hammering on it while there's a breaker bar attached and a friend putting pressure on it. I've heard of guys wondering why it doesn't work even when hit with a fair size hammer, and when asked how much weight they were putting on the breaker bar with it all they could say was "huh"?.

As Gordon said, a cheater piece of pipe over the breaker bar is your friend; I think mine's 4 or 4 1/2 feet long.  Al

Last edited by ALB
Jimmy V. posted:

axle nut removal toolThose axle nuts can be tough to get off. I have a tool VW shops sell that is a wrench that is made to be hit with a big sledge hammer to loosen the axle nuts and this has worked well for me over the past 30 years (BFH ). Oh yes and some torch heat applied to the nut as needed. Good luck getting yours loose.

Jimmy, I have both the 36mm and 46mm tool. I used the cheater bar on the 36mm. I tried using an eight pound hammer but it didn’t budge. I tried different angles striking the tool but was concerned about hitting the fiberglass body. 

Gordon Nichols posted:

If you get a torch and want a lot of heat, Propane won't cut it (no pun intended).

Get a MAPP torch - yellow cylinder, different jet size, LOTS more heat, about the same cost.

I always use an 18" long 1/2" breaker bar with a 6 foot piece of pipe on it, along with a resistance bar attached to the hub bolts.  Heat the nuts up and hang on the end of the pipe and they should slowly loosen (and I only weigh 160 lbs!)

Thank you for the tip on MAPP gas torch type Gordon. That’s the route I’ll take  

I’ll try the cheater bar again, this time with a longer extension attached. I thought a 3’ extension would be enough, I guess I need more leverage. I definitely have the weight! 

 

 

I went to my P mechanic and borrowed a 3/4 inch breaker bar / 6 point 36 mm socket and a 4-5 foot heavy duty pipe and I put my weight(250lbs)  on the end and bounced and it came off.  The 1/2 inch bar broke off, two of them.  I had to use a lock bar between the studs and anchored on the floor of my garage to counter the force I was giving.   It was a really heavy bar. 

 

Anyone use this helping hand ?

Attachments

Images (1)
  • mceclip0

A 3' bar won't even begin to loosen it, heat or no heat (unless your torch is a big Oxy-Acetylene).  You can get a 6' to 8' piece of heavy wall black iron pipe for under $20 bucks.  That, with your weight on the far end of it, should loosen pretty much anything.  Don't jump up and down on it, just put your 2-hand weight on it and lightly bounce it and ride it slowly down.  I can't remember a rear castle nut suddenly breaking loose in a bang or anything - they usually just slowly let go with the proper length pipe extension.

So let's say that the nut is corroded on and you'll need 450+ foot pounds to overcome the corrosion (that's pretty common).  Let's also say that YOU weigh about 180 pounds (stay with me, here...) 

If you have a 6' extension on the breaker bar (and that longer length makes all the difference, here) and you plop your 2-handed 180 pounds out between 5' and 6' from the pivot point, then you'll be able to exert a maximum of 990 ft. lbs. of torque.

But you won't exert ALL of that torque unless ALL of your weight is on the bar (feet off the floor).  Most likely, you'll start pushing down on the bar, the end will arc about a foot and then the nut will just start to turn.  (If it doesn't, I just go find a longer piece of pipe and start over).

That's how it works.  

Archimedes was right.  

"Give me a lever and I can loosen the world" (or something like that).

Gordon Nichols posted:

A 3' bar won't even begin to loosen it, heat or no heat (unless your torch is a big Oxy-Acetylene).  You can get a 6' to 8' piece of heavy wall black iron pipe for under $20 bucks.  That, with your weight on the far end of it, should loosen pretty much anything.  Don't jump up and down on it, just put your 2-hand weight on it and lightly bounce it and ride it slowly down.  I can't remember a rear castle nut suddenly breaking loose in a bang or anything - they usually just slowly let go with the proper length pipe extension.

So let's say that the nut is corroded on and you'll need 450+ foot pounds to overcome the corrosion (that's pretty common).  Let's also say that YOU weigh about 180 pounds (stay with me, here...) 

If you have a 6' extension on the breaker bar (and that longer length makes all the difference, here) and you plop your 2-handed 180 pounds out between 5' and 6' from the pivot point, then you'll be able to exert a maximum of 990 ft. lbs. of torque.

But you won't exert ALL of that torque unless ALL of your weight is on the bar (feet off the floor).  Most likely, you'll start pushing down on the bar, the end will arc about a foot and then the nut will just start to turn.  (If it doesn't, I just go find a longer piece of pipe and start over).

That's how it works.  

Archimedes was right.  

"Give me a lever and I can loosen the world" (or something like that).

Gordon, this reply will alter my commute route home tonight. I’ll try to catch Lowe’s before they close and buy a longer pipe extension along with the MAAP gas torch. 

I’d rather have the tools available than waiting another day. I’ll first give the impact wrench a try tonight since the socket I ordered should be arriving today. If any anything, maybe it will jar loose any rust binding the nut. 

I’ll use the 6’ pipe extension, heat if necessary. One way or another that axle nut is going to come off. 

Thank you for the feedback! 

Gordon leverage is KING...    I have to confess I thought I would never get the nut off myself seeing is was stuck in there with Locktite on my car but LONG BAR and 3/4 inch stuff is strong and my whole 250 went on the end bouncing.  The only thing I am Sorry about is that I could not give you a visual of an Orangutang on the end of the bar  

Last edited by IaM-Ray

It took me about 800 ft.lbs of force to get a rear axle nut off a while back. Turns out that the "expert" that over used an impact wrench putting the nut on actually damaged the threads on the shaft so badly that it has to get replaced. For that reason, if something like penetrating oil and heat don't help enough to get it off with more moderate force, I'd consider cutting the nut off rather than going straight to added horse power. 

Once upon a time,  I had a 5' pipe on the 1/2 breaker bar with just about all my 190 lbs on the end of the bar...the end of the  breaker bar in the 36mm socket snapped off... ( now visualize this)  I went the entire length of the shop dragging the bar,  tripping over my own feet while trying to keep my balance.  The shock that went though my back was unreal a couple of couch days made it better.  

Ray wrote: "The only thing I am Sorry about is that I could not give you a visual of an Orangutang on the end of the bar"

Actually, Ray, I have that visual.  My brother was roughly your size, Ray, (same first name, too) and we were trying to get a few rusted/salted on lug nuts off of a truck wheel with a 24" long, 3/4" drive bat handle with an 8' piece of pipe on it with my brother bouncing up and down on the end.  The visual is appropriate.

Post Content
×
×
×
×
Link copied to your clipboard.
×
×