Skip to main content

Pivot ratio.

Isn’t that the relationship between the movement of the throwout actuator lever to the movement of the clutch pedal?

Like 1/8” at the throwout lever equals 1” at the pedal (like Danny said).  Once you figure out the ratio you’ll know two things:  1.) How far the pedal can push the throw out lever for total movement and 2.) where the throw out lever is when the pedal is at rest (adjustable at the throwout lever).  The ratio will tell you how close the lever needs to be to touching the throwout to the plate when the pedal is at rest in order to get the plate to release the clutch disk with a “normal” clutch pedal stroke.

I used to adjust hydraulic clutches in buses the same way:  Adjust the slave first, so that you’ve got about 1/8” of free play at the throw-out lever, then adjust the pedal end to give you 3/8”-1/2” free play, max, then bleed the circuit.  That should get you in the ballpark and final adjustment just brings the pedal and/or slave ends slightly closer in gap at neutral.

Last edited by Gordon Nichols

Yeah whatever, G. This rig was made and marketed to do what I'm asking it to do on the VW parts I've installed it on. I should not have to calculate any angles or engineer any ratios. The slave ain't pulling enough and it keeps blowing bubbles. The pedal takes a while to come up after I close the bleeder so I'm a little stumped right now. No leaks anywhere I can see (yet). I bled this thing out like a year ago and thought I had a decent stroke on it then. Obviously I do not know my business.

Meanwhile: right front caliper is also leaking. dang. 

I messed with the pedals and the hydraulics for a couple hours today and in between doing that (whilst pondering my life choices) I did a little upholstery work.

The second run of 550 Spyders all had this intriguing bit of frippery at the leading edges of the doors. As previously discussed, there were curled aluminum somethings riveted in the lower front corners, making a sort of Nabisco corner over the lower edge.

These took me like five tries to make to my satisfaction, and what I ended up with is still not quite right.

Above those, presumably to block any air intrusion through the door gaps into the open goddamn cockpit are these baroque rolled bits of vinyl around rubber tubes held in place by machined 1/3-round aluminum tubing screwed to the doors.* Looks something like:

So I cut off a bit of my wife's garden soaker hose, applied the grinder to some alum tubing and

IMG_4145IMG_4144

*"Just why Porsche went to such lengths to trim out a race car is a mystery to me."

–Rainer Cooney, The Spyder Factory

Attachments

Images (2)
  • IMG_4145
  • IMG_4144
Last edited by edsnova

Why did they go to such lengths? The only answer is they were GERMAN. Everything gets complicated when they are involved. They can't help it.

And as far as pedal ratio I was talking the relationship of pedal length to MC push point. So since you duplicated an existing ratio, I think you're good.

If the slave is still blowing bubbles you either have a leak in the MC or maybe one of the fittings somewhere is sucking air. I bled mine by myself with a broomstick through the steering wheel in 2004.

Last edited by DannyP

Well, I think I've finally diagnosed it...

Which is just freakin' beautiful.

Presumably I screwed up the throwout bearing somehow, either by installing it wrong or, more likely, by installing the wrong type. (Any other wagers?)

Either way, apparently it's time to remove the engine and transaxle again.

Nothing's more fun than that, right guys?

Last edited by edsnova
edsnova posted:

Well, I think I've finally diagnosed it...

Pesumably I screwed up the throwout bearing somehow, either by installing it wrong or, more likely, by installing the wrong type. (Any other wagers?)

Either way, apparently it's time to remove the engine and transaxle again.

Nothing's more fun than that, right guys?

Some days... I had a similar moment when I realized that I hadn't even installed the throw out bearing on mine. Good luck!

Yeah I put one in. It's held in with wire clips, which I remember because it took me a minute to grok how they were supposed to work. Seemed to be the right style. 

Anyone have any insight into this? I remember when I did Bridget's new clutch I had to omit a part of the new TOb that was made to fit both old and new style transaxles. Did that on the second try....

This trans is the old style so I figured I was OK... 

Edit:

But of course the pressure plate is different. The pressure plate. The plate that came with the engine is late style, fingers, no collar. See below, circa 2:30

IMG_2726

—which means the TOb can't reach it. CAN'T WORK. GODDAMMIT!

So that means I have to either

1. replace the clutch, or

2. buy and install a late-model conversion/upgrade trans seal/collar kit 

either of which requires the whole friggin thing to come back apart.

 

Attachments

Images (1)
  • IMG_2726
Last edited by edsnova

I feel for you ED !!  I think I have the record for engine R&I though. Only 11 times in 4 months ! Yup, wrong T/o brg,   knicked input shaft seal, two blown oil coolers, oil pressure regulator piston jammed in, broken weld on T/O brg. release lever, leak on camshaft plug in crankcase. no spring on crank seal. A couple more that were optional when I was doing oil temp testing. Got pretty good at it ! Zipper's would have helped. 

When I had the engine apart for the cam plug leak, I installed the Total Seal piston rings.  That turned out to be a real plus.

Over the years, I've always heard a lot about problems with the clutch release system on VW's. It has always seemed like it involved the cable, the tube or the lever. I have often wondered  why nobody came up with a steel rod from the pedal lever all the way to the lever on the bell housing. Possibly it would need a bellcrank where it comes out of the body at the center tunnel. Hydraulic systems always have their issues as well and I have never trusted them. Clutch cables in our cars are seemingly all a different length and therefore difficult to get a replacement that is correct. When we build these cars we have to seriously modify the floor pan, opening them up like a tin can to shorten them and get everything to work again when assembled. It seems like it wouldn't be difficult at that time to install a 5/16" (or even a 3/8") steel pull rod from front to back along with a non-reversing 1 to 1 bell crank at the rear to terminate it and then up to the clutch release lever with another pull-rod. This would eliminate the need for the Boudin tube as well. If done right, the bell crank could be drilled with extra holes to allow lengthening or shortening the stroke........Just a thought.............Bruce

 

 

Yes, exactly that, Ed. It has a sort of snap ring that holds it in place from the flywheel side against the clutch fingers.

Bruce, I don't understand the dislike of hydraulic clutch mechanisms. They are very widely used and more reliable than those cables that are always breaking. I've had my fair share of many broken cables (3 on one Scirocco alone) over the years. Honestly the cable arrangement on early Spyders was a bit Rub Goldberg with the direction-reversing pulley.

I've had only two hydraulic failures. One was the slave in my 5000CS quattro. It was almost 20 years old at that point. The other was the Neal slave in my Spyder, which merely needed to be cleaned. If you flush the brakes and clutch fluid every two years as recommended it's a non-issue.

Ed's problem is one easily solved and is merely a parts compatibility/error having nothing to do with actuation method.

FYI, your Subaru Spyder trans has a master/slave arrangement.

Last edited by DannyP

Danny...As Tom Selleck said in the movie, Quigley Down Under..."didn't say I didn't know how to use one. I said I don't have any use for them".  I've had hydraulic clutch actuators in several of my "project cars" and, as you said,  I will in the next one as well. They are a very expedient way of getting the job done in a pretty good way but are more finicky. Especially when slight leaks occur.  Many people, with limited experience, don't understand some of the critical aspects of how they work. Even though the system seems simple. One example comes to mind regarding piston/cylinder sizing of both Mstr.Cyl and Slave. Another is making sure the fluid lines are not in contact with severe heat sources such as exhaust pipes. In one system, the owner didn't remove the residual valve from the Master cylinder. Another one, the owner had too much angle on the push rod in the full extension position, limiting the release force and travel distance. Another, the slave was too far from the release lever and ran out of travel before the clutch was released. Sometimes it's just better to keep it simple if possible. As you said, you've had your fair share, and so have I, of clutch problems and I have concluded that a good solid mechanical linkage set-up is pretty fool proof for a long time.  How it works is also easily understood  by nearly everyone.     In the end.....There is a place for hydraulic clutch systems but personally, I wish it were not so.

Speaking of Subaru Clutches. How do they compare to the HD units we use on a VW ? The one on my engine looks about the same but I'm not sure. It is made by Subaru and I believe it's used in a Subaru Forester..................Bruce

 

 

Thanks Ray.  Do you know the diameter of your clutch ? I neglected to ask them at Outfront when they changed out my flywheel and took back the Subaru-to-VW bell housing adaptor. One of the guys there said he thought the clutch assy was from a Forester so that wasn't a definite answer. I will have a hydraulic clutch release system in the Spyder (my favorite Ha ha ! ) ...............Bruce

I am not sure but the tranny type is an Impreza TY758  which has the clutch arm,  pull or push I forgot but it works well with the cable and I like the tension on the unit so it works for me and that is what I prefer.   IM makes a hardy cable for it I am told. 

The ratios work quite well and I can row with it up and downshift with ease and it does not have a gap like my 4 speed 3:44 had on my old IM. 

I hope you enjoy it. 

 

 BTW I am not sure on the diameter but the tranny details should allow you to find it easily as it is a stock flywheel and clutch pressure plate set up for a N/A 2.5L engine

FYI , OK build sheet is 4.1 final drive. TY758 donor (2009 onwards)

1st gear 3.454 2nd gear 2.062 3rd gear 1.448 4th gear 1.088 5th gear 0.78

Last edited by IaM-Ray

Taking the Spyder apart from underneath so Cory and I can get the engine and trans out tomorrow. 

IMG_4157

I ordered the clutch ring thing and hope to get it next week. Will probably re-do the oil lines as well, because I just don't like 'em. We'll see when we can get the engine back in after that. 

Also did a final adjustment on my fuel gauge sender before unhooking the battery.

 

Attachments

Images (1)
  • IMG_4157

Removed exhaust, oil filter, lower engine mount nuts, fuel lines, wires and breather hoses. Still gotta do the diagonal breather, coil mount, starter, holy subframe thingy, engine cover, hook up the hoist hooks, take off the (painstakingly just adjusted) swingarm bolts, jack the frame, remove the wheels, calipers and (I guess) hubs (oh crap there's still oil in the trans)....

It is a lot of fun but  if I ever open it up I would change the tranny gearing to the following.  What do you think. 

4.1  R&P                                  Proposed new   R&P 3.9

 

1st gear 3.454 

2nd gear 2.062 

3rd gear 1.448 

4th gear 1.088 

5th gear 0.78                                            fifth gear to 0.735  

tyres are 24.88 inches

             

TO conclude change the R&P 3.9   and  the fifth gear to 0.73.5     5th gear   

This would give you 2700 rpm at 70mph.   

 

 

 @IaM-Ray

  If you look at the calculator below, #1 is what you have (couldn't find a tire size that's exactly 24.88" but the 205/60-15 at 24.69 is very close). Ideally you want the rpm drop of each successive shift to be a little smaller- for general driving this takes the best advantage of an engine's powerband and makes the car easiest to drive (especially if the engine is smaller). With a Subaru engine there's enough power that it still all works- and no worries about slower fan speeds not being able to cool an aircooled engine properly at higher speeds. I would space out 3rd and 4th a little more so the drop into 5th isn't so drastic, but 1st through 4th acceleration must be fantastic! For canyon carving the larger drop going from 4th to 5th does put you at a little bit of a disadvantage, but if you really do like everything more or less the way it is I get that as well.

#2- Lengthening 5th gear makes the 4-5 drop even bigger, but again, if that doesn't bother you, then so be it. The r&p change doesn't change things much (for the money spent), so you have to make that decision.

http://www.teammfactory.com/ca...35/0/3600/3600/1/0/2

 Now check out below- #1 is what you're proposing and 2 is what I would be tempted to do- lengthen 3rd and 4th slightly as well and now that (even bigger) 4-5 hole is gone. The 2-3 and 3-4 shift are still close enough that you won't lose much and when running with the guys in the mountains power in 5th is right there!

http://www.teammfactory.com/ca...35/0/3600/3600/1/0/2

Hope this helps. Al

Did you look at that SB convertible or the KG?

Ok- fixed it...

 

Last edited by ALB

Thanks Al the ratios I have right now Are really nice and if I could just do the 6th and maybe the R&P we could have a cruising gear at 70mph of 2500rpm

So you could put a subie 6 speed but it is a few inches longer and you would need a cable shifter.

You probably would need to lengthen the body like IM-6 frames unless the cross member in the I M frame could be opened and somehow made stronger as you need 4 inches more .

Australia does it 

Upholstery. Made the passenger door top today and went ahead and installed it with the front "roll" piece. Nothing—but nothing—is easy on this thing.

IMG_4179

There's a 3/8-inch gap between the trim piece and the door proper at the top. The bottom (which no one can see) is nice and tight. 

IMG_4182

I ended up clamping the piece to close the gap, but I think I'm going to have to take it apart and reshape it.

IMG_4184

Again, the look we're going for:

My clutch part came yesterday so I'll probably turn my attention back to the drive train for a few days whilst pondering what to do with the interior...

Attachments

Images (3)
  • IMG_4184
  • IMG_4182
  • IMG_4179

Separated the engine from the trans this AM and realized I was unsure of how exactly this clutch ring thingie attaches. My recollection from the old one is the flat coil spring affixed to the back of the ring has to come off to make the part come off; by this I deduce that installation will require my threading said spring back on from behind—after I remove the pressure plate of course. 

Has anyone here done this job? Any advice appreciated.

IMG_4189IMG_4190

Attachments

Images (2)
  • IMG_4189
  • IMG_4190

Update: I did this and put it back together, tested the clutch arm this time with a big wrench. It works.

The clutch ring thing goes on like this:

IMG_4200IMG_4201IMG_4202IMG_4203

Re-torqued the pressure plate to 20 ft-lbsIMG_4204

Married them back up. Quite pissed that a load of gear oil leaked out from the axle boots. The brand new axle boots. WTF?

IMG_4205

Ah well.

Also finished the door top upholstery on the driver's side. IMG_4192IMG_4193

vs

 

 

 

Attachments

Images (8)
  • IMG_4200
  • IMG_4201
  • IMG_4202
  • IMG_4203
  • IMG_4204
  • IMG_4205
  • IMG_4192
  • IMG_4193
Last edited by edsnova

Continued upholstery work. Test fit the top of the firewall piece (chipped the paint! Grrr!). Stapled and glued the last (lowest) bit of velcro to it. Started making two filler pieces to fill small gaps in side of firewall just behind the doors.

IMG_4233IMG_4234

Cut, bent, drilled and welded the "emergency top" mounts--they'll help pin the vinyl to the firewall at the sides. Primed them.

IMG_4239

Test fit Knecht styler air filter. Had to grind small reliefs in the velocity stacks. OK.IMG_4240

Attachments

Images (4)
  • IMG_4233
  • IMG_4234
  • IMG_4239
  • IMG_4240

@edsnova — this looks dynamite! 

I feel your pain with the Vintage Speed Air Cleaners. I had to do the same with my velocity stacks. Pat Downs and I did this part together, and he was not impressed! 

I used EMPI filters in there and removed that grey foam that came it with it; it seems to fall apart easily and seems highly suspect. If you need another set of EMPI filters, I have some. 

Anand

Post Content
×
×
×
×
Link copied to your clipboard.
×
×